How do I log in to the encoder’s local web setup interface
There are two different ways to connect to the Encoder's local web interface:
Using an automatic Wi-Fi hotspot that is created on new encoders that have no configuration
(useful for setting up and configuring new units quickly)Connecting a PC directly to one of the encoder’s LAN ports
(the normal method for configuring an encoder)
Option 1: Using a laptop via the on-board Wi-Fi hotspot
Note: HD-IP200 and HD-IP250 require a supported Wi-Fi dongle to be plugged in before powering to use this mode.
A new unit with no configuration (or a factory-reset unit) will create a temporary Wi-Fi Access Point when it is powered up for the first time. The purpose of this Wi-Fi network is to allow Wi-Fi enabled computers to connect to the encoder and configure the device. (This hotspot will remain active for 30 minutes.)
On a PC, search for a Wi-Fi Access Point Name in the form XXX-YYYYYYYYY
(where X equals the model number, and YYYYYYYYY matches the first part of the encoder’s serial number)Connect to the network, using password as the Wi-Fi password
Open a web browser on the setup laptop/PC and enter the following URL: http://192.168.100.1.
Option 2: Using a laptop via a LAN interface
To access the local web interface, ensure that the setup laptop/PC can connect to the device:
Connect your PC to one of the network ports on the encoder (or via a supported USB to Ethernet adapter). From the table below determine the IP Address of the selected port:
IP200 | LAN – 192.168.10.1 |
| USB Ethernet – 192.168.12.1
|
IP250 | LAN – 192.168.10.1 | CAMERA – 192.168.11.1 | USB Ethernet – 192.168.12.1
|
IP470 | LAN – 192.168.10.1 | POE1/2 192.168.11/12.1 | USB Ethernet – 192.168.20.1
|
EdgeVis MiniCam |
|
| USB Ethernet – 192.168.20.1 |
HD-Q800 | LAN (AUX) – 192.168.10.1 |
| USB Ethernet – 192.168.12.1 |
4K-R800 | LAN – 192.168.10.1 | ECU LAN – 192.168.11.1 | USB Ethernet – 192.168.20.1 |
Video Router (EVVR-1 / EVVR-4 / EVVR-1R / EVVR-4RL) | LAN1 – 192.168.10.1 | LAN2 – 192.168.11.1 | USB Ethernet – 192.168.20.1 |
Once connected:
On the PC open the IPv4 network configuration page for the PC’s Ethernet port.
(If necessary, refer to these instructions)
Select the Use the following IP address radio button and enter these settings in the following two fields:
· IP address: 192.168.X.2 (where X is taken from the IP Address of the selected port in Step 1)· Subnet mask: 255.255.255.0 and then click OK to apply.
Open a web browser on the setup laptop/PC and enter the following URL: http://192.168.X.1
(where X is the same as the IP Address of the selected port in the table above – e.g. 192.168.10.1)
Firmware Version 8.5 Security Enhancement - Encoder local web configuration interface now utilises SSL
As of encoder firmware version 8.5 and above the local web interface now uses https instead of http.
On initial connection you will see a security warning that you have to accept to proceed - this is because the certificate is self-signed and is expected behaviour.
If you attempt to visit the old http://[encoder ip address]/ URL you will be automatically redirected to the new https://[encoder ip address]/ URL.
Logging into the setup web interface
Regardless of the method used, the web browser should now show the login screen for the encoder:
The default password is password
For security reasons the encoder will now prompt to change the default password to something more secure.
Firmware Version 8.5 Security Enhancement - Secure password requirements for local web configuration
As of encoder firmware version 8.5 and above:
password complexity rules have been introduced requiring the use of a strong password
a timed auto lock-out feature has also been introduced should someone on the same network attempt to guess the login incorrectly.
Once logged in the encoder’s dashboard is loaded:
The dashboard presents the status of the encoder, showing red crosses where an issue requires attention, or a green tick to indicate that section of encoder configuration is operating correctly. The encoder will also display a help tip if any crucial encoder settings are still blank and require configuration.
Wireless Access Point
If supported by the encoder (or when used in combination with a supported USB Wi-Fi adapter) it is possible for the encoder to create its own Wi-Fi hotspot, which allows the user to directly connect to the encoder remote configuration over Wi-Fi, remotely download video recordings over SFTP, or allow Wi-Fi cameras to connect directly to the encoder.
The encoder has three modes of operation:
Use for communications – the Wi-Fi will only connect to other Wi-Fi routers (as configured in the communications settings page).
Use as an access point – the Wi-Fi will broadcast a Wi-Fi access point. This will ignore any Wi-Fi configuration settings in the communications settings page, and Wi-Fi can’t be used to connect to EdgeVis Server.
Switched – the ability to switch between the first two options remotely (using EdgeVis Client or EdgeVis Server). This is useful when normally the encoder should transmit to EdgeVis Server using Wi-Fi but switch to access point mode during ‘drive-by’ collection of recordings using SFTP.
When configured to allow a Wi-Fi hotspot there are several options available:
Network name – the name of the Wi-Fi network that will be visible to other Wi-Fi users.
Wi-Fi password – the password required to connect to the Wireless Access Point
Auto assign IP Addresses (DHCP) – normally left on, this provides an IP Address to any user who connects
Encoder IP Address – this is the IP address to use when accessing the encoder when connected via the wireless access point
Inactivity timeout – (switched mode only) when switched by the user into access point mode the encoder will automatically revert to communication mode after the encoder has sent/received no network traffic on the access point for the supplied number of minutes.