The body worn web configuration can be found here:

Server Address: The address of the EdgeVis server this device is to connect to

Allow secure connections: Requires crypto firmware to be installed on the device. Download the encryption pack from the EdgeVis server and upload to the configuration page.

By default, the system will use the encoder name configured against the user in video vault. However, the device name can be used as the EdgeVis Encoder name. To use this mode, enter the encoder password to use in the “Use device name as encoder name” field. All EdgeVis encoder must use the same password when using this mode.

Notification sound volume: The device volume to be set for device notification sounds

Settings Password: Set a password here to lock the device settings. If left blank the settings will not be locked

Silent mode on startup: Device will be in silent mode when undocked. In silent mode the device will not flash any LEDs or make any notification sounds

Enable Audio: Enable audio for any recordings and streaming. Audio needs to be enabled on the streaming profiles as well

Maximum FPS: The Frames per second to record. This also is the maximum fps the device can stream at

Maximum Width/Height: The maximum size of the video frame. This will be the frame size of the full resolution capability and the maximum frame size the device will stream at

Aspect Ratio: The aspect ratio to stream at. This does not affect the recording aspect ratio

Auto IR: Auto enable the IR lamps and camera when the light drops below a certain level. The IR lamps will affect battery performance

Enable recording on start: The device will start recording as soon as it’s undocked

Record while live streaming: The device will automatically start recording if the device starts to stream to remote viewing client. It will stop recording automatically when the streams stops

Recording mode: Determines what the device will do when the recording disk is full

Disk full alarm threshold: If the disk fills up, an alarm can be generated to inform a system administrator that the device disk is filling up

Maximum disk quota: Determines how much of the disk to use for recordings.

Show pre-recording indication: Show a pre-recording indicator on the device screen

Pre-recording duration: Device will pre-record for this duration. On pressing the record button the device will store the pre-recording duration to disk. Pre-recording will affect the battery performance of the device.

Record audio while pre-recording: While pre-recording the device can optionally record audio

Show post-recording indication: Show a post-recording indicator on the device screen

Pre-recording duration: Device will continue to record for a set time after the operator presses the stop recording button.

Archive encryption enabled: Recordings can be encrypted on disk. Requires crypto firmware to be installed on the device

Enables GPS location data. Location data will be recorded on the device and sent to the EdgeVis server. Shorter update times will affect battery performance. We suggest no lower than 30 seconds.

Leave these settings blank to use the default APN settings of the SIM card.

If setting a custom APN, the Name and APN fields must be set. The name is for information only. The Username and password are optional.

Enable or disable cellular data roaming on the device. Requires version 7.2.12 and above. If this is not present in the config file the application will not change the current device setting.

Enable Wi-Fi on the device. When enabled, the Wi-Fi will be turned on when the device is assigned and undocked. An SSID and Password can optionally be added. If set, it will be added to the Wi-Fi list on the device. If there are multiple Wi-Fi configured on the device, it will not force the device to connect to this Wi-Fi.

Configure the required action of each of the buttons on the device.

Bookmark: Set a bookmark on the recording. Bookmarks can be viewed in Video Vault

Toggle silent: Turn silent mode on. The LEDs will not illuminate and the device will not make any sounds

IR toggle: Toggle the IR lamps. This cannot be set when the Auto IR is enabled

Face Recognition: Run the face recognition algorithm on the camera and send faces to EdgeVis server. This requires the Face Recognition system

Recording Start Stop: Start and stop the recordings

Alert: Send an Alert to the EdgeVis server.

Disabled: Disable this button

Set the operation of the device LEDs. A state with a higher priority will override a lower priority.

Available application events and groups:

Each group of settings can have a Priority and colour

Each event can determine the state of the LED

For example, the Battery group can have a high priority, using the Red LED. With Battery not low set to OFF and battery low set to Flashing Fast.

Set the vibration and notification sounds to make. Not all devices support vibration.

Each event can either

Modify the TVI streaming settings for each connection profile. If you are unsure, leave the settings at the defaults

Log Level: Only set if requested to by Digital Barriers support

Device Log: Set the device log frequency. Leave at 5 Minutes unless requested by Digital Barriers support. Device logs are uploaded to Video Vault when docked

Crash report: Only set if requested to by Digital Barriers support

​